NS0-182 Online Practice Questions and Answers

Your customer has filled out the customer installation worksheet. However, the customer's network environment is not set up and ready for the new ONTAP 9.5 system. The customer requests that you install the system and states that they will finish the configuration when they have acquired the appropriate network connections.

Which two statements are correct about this scenario? (Choose two.)

A. You should cable a cluster so that the clusters interconnect traffic is on a separate network from all other traffic.

B. You cannot install an ONTAP system without having the customer network configuration.

C. You should cable all of the controllers and disk shelves, power on the system, and then leave the system as-is for the customer to configure.

D. A cluster can be created without data network connections, but it must include a cluster interconnect connection.

After you install a new cluster with ONTAP 9.5 software, you want to create a new broadcast domain. During the creation of the broadcast domain, you receive an error that there are no free ports available.

What is the reason for this error message?

A. By Default, all ports are bound to the "Default" broadcast domain. To create a new port, remove the needed ports from the "Default" broadcast domain and create a new IPspace.

B. By Default, all ports are bound to the "Default" broadcast domain. To create a new port, remove the needed ports from the "Default" broadcast domain.

C. Before you configure a new broadcast domain, you should create a new IPspace.

D. You can create a new broadcast domain only within the CLI.

You create a new CIFS data LIF with the default failover group.

In this scenario, where will the new LIF failover if the node that owns the new LIF panics?

A. to any port in the cluster that is administratively up

B. to any port in the cluster that is operationally up

C. to any available port in the same subnet

D. to any available port listed in the broadcast domain

Recently, your 2-node FAS8020 cluster was upgraded from ONTAP 8.3 to ONTAP 9.5. You have just added two FAS8060 nodes to the cluster. You have executed Config Advisor to verify your work. Config Advisor tells you that the cluster ports on the original two FAS8020 nodes have Flow Control set to FULL.

In this scenario, to what should the Flow Control setting on the FAS8020 ports be set?

A. Flow Control should be set to SEND.

B. Flow Control should be set to ALL.

C. Flow Control should be set to RECEIVE.

D. Flow Control should be set to NONE.

Select the Exhibit tab.

You install a new FAS2552 HA using a DS2246 disk shelf and ONTAP 9.5 on a customer site.

Referring to the exhibit, which two statements describe what is required to get an HA cabled system? (Choose two.)

A. Insert a cable from right controller port 0a to the IOMB square, and from port 0b to the IOMA square, then cable in-band ACP.

B. Insert a cable from right controller port 0a to the IOMB square, and from port 0b to the IOMA circle.

C. Insert a cable from left controller port 0a to the IOMA circle, and from port 0b to the IOMB circle, the cable in-band ACP.

D. Insert a cable from left controller port 0a to the IOMA square, and from port 0b to the IOMB circle.

Which two configurations use root-data-data partitioning? (Choose two.)

A. FAS8080 with 1.8 TB external SAS drives

B. AFF A800 with 3.8 TB internal NVMe SSD drives

C. FAS2650 with 1.8 TB internal SAS drives

D. AFF A220 with 3.8 TB internal SSD drives

You are preparing for a new installation. While determining the most suitable version of ONTAP software to deploy, you want to verify the ONTAP 9 release cadence to ensure that you are deploying a Long Term Service (LTS) release.

In this scenario, where would you find this information?

A. Visit the NetApp Support site.

B. Visit the ONTAP 9 Documentation Center site.

C. Visit the Interoperability Matrix Tool site.

D. Visit the Hardware Universe site.

When planning the installation of a new ONTAP 9.5 cluster for a customer, which three steps should you perform? (Choose three.)

A. Complete a Service Event Report.

B. Use Config Builder to create a configuration spreadsheet.

C. Review the hardware components in Hardware Universe.

D. Open a support case to prepare for the installation.

E. Search for Technical Support bulletins for the hardware.

After the installation of a new 2-node cluster, you want to make sure that AutoSupport is working as expected from the cluster.

In this scenario, what are two ways to trigger a new Auto Support? (Choose two.)

A. Use the ping command on the mailhost.

B. Use the OnCommand UnifiedManager GUI.

C. Use the OnCommand System Manager GUI.

D. Use the system node autosupport invoke -type test command.

You are performing a nondisruptive image upgrade of a CN1610 switch. You verify that there are no path failures on the switch.

What is the next step in this process?

A. Run the write memory command.

B. Run the reload command.

C. Backup the current running image using the copy active backup command.

D. Reboot the switch.