HP2-Z37 Online Practice Questions and Answers

Which credential is required to validate SNMPv2c write requests?

A. Community string

B. Scheme

C. MD5 authkey

D. AAA authentication

A network administrator establishes an aggregated link between an HP Comware and ProVision switch. VLAN 1 is untagged and VLANs 2 and 3 are tagged. The administrator configures these commands on the Comware switch:

The administrator configures theses commands on the ProVision switch:

Some of the links in the aggregated link become blocked.

Which Comware configuration should the administrator apply to the Comware switch to resolve this issue?

A. interface bridge-aggregation 1link-aggregation mode dynamic

B. interface bridge-aggregation 1link-aggregation type lacp dynamic

C. interface bridge-aggregation 1link-aggregation mode static

D. interface bridge-aggregation 1link-mode type lacp

Which statement correctly defines the management capabilities of an HP MultiService Mobility (MSM) access point (AP)?

A. The AP only supports controlled mode.

B. The AP operates in autonomous mode by default, but can be changed to controlled mode.

C. The AP operates in controlled mode by default, but can be changed to autonomous mode.

D. The AP only supports autonomous mode.

Refer to the exhibit.

The topology shown on the left of the exhibit illustrates a traditional three-tier architecture. Which technology allows a company to simplify their network with a two-tier topology as illustrated on the right of the exhibit.

A. Intelligent Resilient Framework

B. Software-defined Networking

C. Multiple Spanning Tree Protocol

D. Equal Cost Multi-Pathing

Refer to the exhibit.

A network administrator is upgrading the operating system on an HP Comware switch. When copying the new image from a TFTP server to the flash of the switch, the process fails because there is not enough flash to store the new operating system. The new operating system is 3.2MB in size. The administrator then executes the commands shown in the exhibit above.

Which action should the administrator perform to solve this problem?

A. Execute the reset recycle-bin command, and perform the TFTP transfer again.

B. Execute the clear flash command, and perform the TFTP transfer again.

C. Reformat flash, and perform the TFTP transfer again.

D. Execute the delete old.app command, and perform the TFTP transfer again.

An HP switch learns identical valid routes with different protocols. How does the switch choose which route to add to its IP routing table?

A. It adds the route with the highest administrative distance, or route preference.

B. It adds the route with the highest cost.

C. It adds the route with the lowest cost.

D. It adds the route with the lowest administrative distance, or route preference.

A server connects to a port on an HP Comware switch. The network administrator wants to ensure that:

Which statement describes how the administrator can accomplish this?

A. The administrator must manually configure the port as an STP edge port.

B. The administrator can lower the port's root path cost to zero.

C. The administrator can accept the default behavior of auto-edge.

D. The administrator can configure the port as an MSTP master port.

Refer to the exhibit.

Exhibit: Network diagram and routing tables

Why does traffic from PC1 fail to reach PC2?

A. Only static routes have been enabled

B. The subnet mask is incorrect on the routers

C. There is no route back from router B

D. A default gateway setting is incorrect

Refer to the exhibit.

A network administrator sets up OSPF in part of the network topology shown in the exhibit. The Comware-1 switch is already configured. The administrator needs to configure ProVision-1 so that:

-OSPF includes VLANs 10 and 20 in the routing process.

-

The router ID of 1.1.1.1 is assigned to the switch.

-

The ProVision-1 switch can successfully build a neighbor adjacency with the Comware-1 switch. Which configuration should the administrator apply to the ProVision-1 switch to meet these requirements?

A.

router-id 1.1.1.1router ospf area 0vlan 10ip ospf area 0vlan 20ip ospf area 0

B.

router ospf router-id 1.1.1.1area 0 vlan 10area 0 vlan 20enable

C.

router ospfrouter-id 1.1.1.1area 0 vlan 10area 0 vlan 20

D.

ip router-id 1.1.1.1router ospfarea 0enablevlan 10 ip ospf area 0vlan 20 ip ospf area 0

A network administrator configures this command on an HP ProVision switch:

vlan 30 ip helper-address 10.0.3.253

The switch is able to ping 10.0.3.253. After the administrator configures the command, users in VLAN 30 report that their PCs fall to acquire addresses using DHCP.

What should the administrator ensure?

A. that the switch is configured with a dynamic IP routing protocol

B. that the switch has DHCP relay functions enabled

C. that the switch has DHCP server functions enabled

D. that the switch has an IP address on VLAN 30