HP2-Z34 Online Practice Questions and Answers

An administrator is configuring an HP switch to run SPBM. Which Spanning Tree Protocol (STP) configuration is required?

A. Disable STP.

B. Ensure that the switch with the lowest IS-IS router ID has the lowest bridge priority.

C. Set the spanning tree mode to ECT.

D. Map all B-VLANs to MSTP instance 4092

To provide redundancy, a company has multiple data centers that use server virtualization. What is a networking requirement for this scenario?

A. less bandwidth at the server access layer and more bandwidth at the distribution layer than in a nonvirtualized network

B. physical network segmentation and isolation implemented at Layers 1 through 7

C. localized storage volumes that are isolated within each data center

D. extension of Layer 2 connectivity across the data centers

What is the purpose of the nickname in TRILL switch settings?

A. The nickname identifies the TRILL region and must match on every TRILL RBridge in the region.

B. Administrators can use the nicknames to identify switches in CLI output.

C. The nickname is the first factor for electing a root bridge

D. TRILL RBridges use the nicknames as source and destination addresses in TRILL headers

Several VPN instances have been set up on an HP Comware switch. What should the administrator do to ensure that no VPN instance uses up too many switch resources?

A. Apply a service policy to each instance to assign that instance a percentage of resources

B. Bind each instance to a specific port group or ASIC

C. Set a maximum number of routes that each instance can have in its routing table.

D. Set a CPU weight for each VPN instance to control how much of the CPU the instance can use.

Refer to the exhibit The company wants to use TRILL in the backbone links shown in the exhibit. Servers use VLANs 10, 20, and 30 and should be able to communicate across the backbone. On which Switch 1 interfaces should the administrator enable TRILL?

A. VLAN interface 1 only

B. VLAN interfaces 1,10, 20, and 30

C. interfaces Forty1/0/49 and Forty1/0/50 only

D. interfaces Ten1/0/1 to Ten1/0/48, and Forty1/0/49 and Forty1/0/50

Refer to the exhibits Exhibit 1 This data center topology is being set up to use SPBM. VMs in the same subnet should be able to communicate at Layer 2 and be isolated at Layer 2 from other subnets. VS110010 was created for VLAN 10 as shown in Exhibit 2. The administrator is configuring a service instance for the VLAN 10 traffic on Switch 1 interface Ten1/0/1.

What is the correct encapsulation mode?

A. s-vid101

B. ta99ed

C. default

D. s-vid10

To support FCoE traffic, a switch port needs to use Application TLVs to communicate application priority information to a Converged Network Adapter (CNA). The setup process includes the configuration of an Access Control List (ACL). What is a valid ACL?

A. Advanced ACL that selects traffic by UDP source port

B. Advanced ACL that selects traffic by TCP source port

C. Standard ACL that selects traffic by source IP address

D. Ethernet ACL that selects traffic by Ethertype

Refer to the exhibit An administrator is establishing an MPLS domain to allow communication between 10.1.0.0/16.10 2 0 0/16. and 10.3 0.0/16. The solution will use OSPF routing and LDP. On which PE and P devices should these protocols be configured?

A. All P and PE devices should be configured with MPLS, but only P devices need OSPF and only PE devices need LDP.

B. All P and PE devices should be configured with MPLS, LDP. and OSPF.

C. All P and PE devices should be configured with MPLS, but only PE devices need OSPF and LDP.

D. All P and PE devices should be configured with MPLS and LDP. but only PE devices need OSPF.

What is the correct use case for implementing priority flow control (PFC) on a switch port?

A. The port carries data and storage traffic. PFC should be applied to the priority queue that is assigned to storage traffic.

B. The port carries multimedia voice and video traffic PFC should be applied to the queues with a lower priority than multimedia traffic

C. The port carries data and storage traffic PFC should be applied to the queues with a lower priority than storage traffic.

D. The port carries multimedia voice and video traffic PFC should be applied to the priority queue that is assigned to multimedia traffic.

HP Comware Switch 1 connects to servers with Converged Network Adapters (CNAs) that send data and FCoE storage traffic Switch 1 should forward all FCoE traffic to an upstream FCoE switch. Switch 2 which will handle all the FLOGI requests, zoning, and FC traffic forwarding.

What is the correct FCoE mode setting for Switch 1?

A. NPV

B. FCF

C. disabled

D. hybrid